Contact
Products & Services
From custom fabrication and specialty metals to advanced laboratory equipment, we provide reliable solutions tailored to exact industry specifications.
Our Products
High-Performance Laboratory & Industrial Products
Teflon test tubes and other Teflon products
All of our test tubes are made of the highest quality raw materials.
We only use 100% virgin PTFE Teflon rods made in North America only. We do not use any mechanical grade or recycled Teflon, or injection molded PTFE-nylon mixed material for injection molded “Teflon” products.
All of our Teflon products machined of this high-quality material and resist heat up to 260 ℃. Our tube surfaces, both inside and outside, are extremely smooth for easier cleaning to help avoid any contamination.
We are one of the largest and most experienced Teflon test tube producers in the world! We sold over 400,000 Teflon Test tubes in the past 20 years.
We offer extremely competitive pricing.
Many of the largest assay and geochemical labs use our test tubes.
Unlike most of our competitors, we are able to offer custom sizes and styles made to your specifications even for smaller quantities. Our Teflon test tubes are available in any length, any diameter, with or without a top rim, with the choice of round, flat or tapered bottom.
25 ml Standard Teflon Test Tube
Rounded inside bottom
Rounded or flat out side bottom
20 mm outside diameter
17 mm inside diameter
98 mm length
22.6mm x 5 mm lip
Maximum service temperature 260 ℃
Weight: approx. 25 grams
50 ml Standard Teflon Test Tube
Rounded inside bottom
Rounded or flat out side bottom
26.5 mm outside diameter
23 mm inside diameter
98 mm length
28.6 mm x 5 mm lip
Maximum Service temperature 260 ℃
Weight: approx. 40 grams
Titanium test tube racks and other Titanium products
These test tube racks are designed to fit our HB-80-195 and HB-120-195 hot blocks, using the 25 or 50
ml Teflon test tubes. We can also make custom sizes to your request.
Sits on the hot block on 4 Teflon support legs.
Material: Grade 2 Ti sheet metal, 0.063”-0.125” thickness.
Also available: Titanium forks to move Teflon test tubes and Ti hot water baths in any size.
Aluminum anodized and Teflon coated High Heat electric
Teflon test tube heating blocks and Corrosion resistant
electric high heated hotplates
The Aurum Hot Blocks and Hot Plates are designed specifically for geochemical and assay
laboratories. This system was designed for high sample throughput, maximum durability under
the most extreme corrosive environment, and maximum simplicity. Up to 225℃ (up to 345℃ for
hot plate only) service temperature. Compact design to maximize your fume hood space. All
units available CSA or UL approved if requested.
The standard configuration holds 80 25ml test tubes (2 racks of 40, each one in a 4x10
arrangement to match most commercially available test tube racks). Also available a larger Hot
Block holding 120 50ml test tubes (3 racks of 40, each one in a 4x10 arrangement). Unlike most
commercially available hot block systems, custom configurations are also available to match
your existing vessels and processes.
All electrical components are sealed in the block, using Ti cover plates outside, titanium strip
heater conectors for corrosion resistance. The controller is in a separate titanium enclosure, for
mounting outside of the fume hood. It is connected with a 5 feet maximum cable length, covered
by convoluted PTFE tubing with Titanium connectors to the block.
The entire top surface of the Hot Block is constructed of a single piece 3.5” (2.5” for hot plate)
thick anodized and Teflon coated aluminum block, (hot plate only hard anodized) for easy
cleaning and maximum corrosion resistance.
Most commercially available units, which usually have a plastic or stainless steel enclosure are
designed for low temperature (max 150 ℃). Plastic enclosures tend to warp and deform,
exposing the interior of the unit to further corrosion. Usually graphite blocks are used for easy
and cheap production. Stainless steel enclosures corrode rapidly, increasing the chance of
sample contamination.
In our product the heating elements are widely available ceramic stainless steel strip heaters
which are fully enclosed. These strip heaters are inexpensive and designed to be quickly and
easily replaceable by any qualified electrician with no special tools required.
Matching titanium test tube lifting trays and Teflon test tubes are also available to maximize your
productivity and sample throughput.
Standard HB-80-195
Hot Block holds 80 25ml tubes:
Size: L14” X W11” X H5.25+1”leg
Voltage: 240V
Power: 3000W (4X750W strip heaters)
Amp: 12.5A
Weight: 13.5 kg with control box.
Service temperature: 50-215 ℃.
Maximum temperature difference in the Hot Block cavities of the set temperature +-5 ℃.
Warming time to 195℃ from room temperature 1 hour or less. (No tubes in the cavities and hood fan off)
Cable connector on the long side. Optional on the left or right side.
Note: Also works perfectly @ 208V as most available industrial power in north America.
Large Hot Block HB-120-195
Hot Block holds 120 50ml tubes:
Size: L20” X W16.75” X H5.25”+1” legs
Voltage: 240V
Power: 5000W (4X1250W Strip heaters)
Amp: 21A
Weight: 29.5 kg with control box.
Service temperature: 50-215 ℃.
Maximum temperature difference in the Hot Block cavities of the set temperature +-5 ℃.
Warming time to 195 ℃ from room temperature 1.1 hour max or less. (No tubes in the cavities and hood fan off).
Cable connector on the long side. Optional on the left or right side.
Note: Also works perfectly @ 208V as most available industrial power in north America.
Hot plate HP-345
Size: L24” X W18” X H5.25+1” legs
Voltage: 240V
Power: 6000W (4x1500W Strip heaters)
Amp: 25A
Weight: 42.5 kg with control box.
Service temperature: 50-345 ℃.
Maximum load (weight on top): 50kg
Hard anodized surface, 1/16” thickness Ti enclosure and connectors.
No auto reset thermostat installed. In case of the overrun will not exceed the 375 ℃ temperature.
Maximum temperature difference on the Hot Block surface of the set temperature ±7 ℃.
Warming time to 345 ℃ from room temperature 1.2 hour max or less, if you use the thermal blanket during the warm up period (supplied for free) and not running fan in the hood.
Cable connector on the long side. Optional on the left or right side.
Note: Also works perfectly @ 208V as most available industrial power in north America.
Digitally controlled heated test tube shaker
Aurum Heated shaker is designed specifically for geochemical and assay laboratories. This
system was designed for high sample throughput, maximum durability under the most extreme
corrosive environment and maximum simplicity. Maximum 150 ℃ service temperature. Compact
design to maximize your fume hood space. All units available CSA or UL approved also if
requested.
The standard configuration holds our 50ml test tubes (10 X 8 arrangement)
Also available with custom size tube or arrangement to your specifications.
The shaker block is interchangeable in a few minutes easily to use different size of tubes or
arrangements.
All components are protected from the high corrosive environment using a titanium enclosure.
The entire shaker block constructed of a single piece of 2” thick hard anodized and Teflon
coated aluminum block for long life span.
Inconel Crucible trays
Inconel Crucible trays made of high heat Inconel 600 alloy for up to 1200 ℃ service
temperature. Available any custom size and layout.
Crucible holders for automated fusion machines
Our products are cheaper than OEM and are constructed of a superior quality Inconel
alloy for long life. Also available in any customer requested size and shape.
References
We have worked for many different clients over the years, including large global
businesses. This is only a small sample of the various companies and industries:
• ALS Laboratory Group (formerly
Bondar Clegg Canada Ltd.)
• Blue Coast Research Inc.
• Bureau Veritas Commodities Canada
LTD
• Steward Assay and Enviromental LLC
• Prolab System of Kingdom of Bahrain
• Lawrence Berkeley National
Laboratory.
• Met Solve Analytical Service
References and contact information is available upon request.
Frequently Asked Questions
Got questions about our detailing services? Find quick answers to common queries in our FAQ section below!
Which industries does Aurum Resources Inc. serve?
We serve assay, geochemical, metallurgical, chemical laboratory, mining, electronics, and industrial automation industries.
Do you provide custom fabrication services?
Yes, we specialize in custom design, machining, and fabrication of metals and engineered plastics according to client specifications.
What materials do you work with?
We work with titanium (all grades), stainless steel, aluminum, nickel-based alloys, precious metals, Teflon, nylon, Delrin, and other engineered materials.
Can you manufacture high-temperature laboratory equipment?
Yes, we design and fabricate high-heat equipment, including heating blocks, crucible trays, and specialized components for demanding applications.
Do you design and build CNC or control systems?
Yes, we offer design, engineering, and fabrication of numerical control (CNC) systems tailored to industrial requirements.
What makes Aurum Resources Inc. different from other machine shops?
We combine extensive machining expertise with real laboratory experience. This allows us to understand client requirements and deliver precise, application-focused solutions.